1. Analysis of body measurements, measurement statistics, analysis of information of the  Department of quality management (DQM) on problems and systematic defects. 2. Improving the design of existing technological equipment, aimed at further improving the technical level, production efficiency, as well as improving the quality and reliability of products. 3. Timely and high-quality implementation of technical tasks aimed at improving the quality and stability of the geometry of the body, improving the assembly of the body. 4. Definition of the necessary control points and mapping the measurement of control points on the bodies and nodes in the programs Metrolog 4x/XG, Polywoks via the different CMM. 5. Reduction in the number of points measured on the body beyond the tolerance. 6. Reducing the number of systematic defects of the body. 7. Audit and monitoring of welding equipment of stands and lines for welding bodies of the Renault B0 family (Logan, Sandero, Largus). 8. Analysis of statistics of measurements of bodies and assemblies, as well as welding stands and conductors of the B0 family. 9. Organization and tracking of pilot batches of bodies in production shops. 10. Organization and carrying out assembly tests on draft bodies of the B0 family. 11. Analysis of the results of pilot batches and assembly tests on bodies of the B0 family. 12. Analysis of systematic defects revealed in the audit of the assembled car, related to the geometry of the body. 13. Analysis of systematic defects related to the geometry of the bodies of the B0 family according to the data of the Department of quality management. 14. Adjustment of equipment of welding stands and welding lines of the B0 family. 15. The issuance of technical specifications for the manufacture of additional equipment, control devices, templates, etc., and the modernization of existing equipment. 16. Acceptance, certification and development of technical processes for the operation of control devices, accessories, templates, etc. 17. Providing feedback to the shop of assembly and shop of acceptance of cars. 18. Ensuring the exchange of information with the quality management department. 19. Development of technical requirements, procedures, technical processes, additional documentation on the direction of quality and stability of the geometry of the car. 20. Development, implementation and maintenance of technological documentation (procedures, instructions, regulations, etc.) for the QMS up to date.   Professional duties of working with staff. 1. Control over observance of measures of labor protection, environmental safety, and the quality of work. 2. Compliance with the methodology of workplace organization according to the 5S system. 3. Work to train staff in new methods of control and measurement.

Targeted professional responsibilities 1. Analysis of body measurements, measurement statistics, analysis of information of the Department of quality management (DQM) on problems and systematic defects. 2. Improving the design of existing technological equipment, aimed at further improving the technical level, production efficiency, as well as improving the quality and reliability of products. 3. Timely and high-quality implementation of technical tasks aimed at improving the quality and stability of the geometry of the body, improving the assembly of the body. 4. Definition of the necessary control points and mapping the measurement of control points on the bodies and nodes in the programs Metrolog 4x, Caligo using the Zeiss and Faro CMM. 5. Reduction in the number of points measured on the body beyond the tolerance. 6. Reducing the number of systematic defects of the body. 7. Audit and monitoring of welding equipment of stands and lines for welding bodies of the Patriot family (Patriot, Pickup, Profi). 8. Analysis of statistics of measurements of bodies and assemblies, as well as welding stands and conductors of the Patriot family. 9. Organization and tracking of pilot batches of bodies in production shops. 10. Organization and carrying out assembly tests on draft bodies of the Patriot family. 11. Analysis of the results of pilot batches and assembly tests on bodies of the Patriot family. 12. Analysis of systematic defects revealed in the audit of the assembled car, related to the geometry of the body. 13. Analysis of systematic defects related to the geometry of the bodies of the Patriot family according to the data of the Department of quality management. 14. Adjustment of equipment of welding stands and welding lines of the Patriot family. 15. The issuance of technical specifications for the manufacture of additional equipment, control devices, templates, etc., and the modernization of existing equipment. 16. Acceptance, certification and development of technical processes for the operation of control devices, accessories, templates, etc. 17. Providing feedback to the shop of assembly and shop of acceptance of cars. 18. Ensuring the exchange of information with the quality management department. 19. Development of technical requirements, procedures, technical processes, additional documentation on the direction of quality and stability of the geometry of the car. 20. Development, implementation and maintenance of technological documentation (procedures, instructions, regulations, etc.) for the QMS up to date. Professional duties of working with staff. 1. Control over observance of measures of labor protection, environmental safety, and the quality of work. 2. Compliance with the methodology of workplace organization according to the 5S system. 3. Work to train staff in new methods of control and measurement.

CMM operator (in fact, acting engineer for quality (geometer)) Professional duties of working with staff. 1. Control over observance of measures of labor protection, environmental safety, and the quality of work. 2. Compliance with the methodology of workplace organization according to the 5S system. 3. Work to train staff in new methods of control and measurement. Targeted professional responsibilities for measurement, monitoring and analysis of defects. 1. CMM programming (full body and serial measuring points) for 3D measurements in the software METROLOG XG and PC DMIS. 2. Compiling a report based on the data obtained during the measurement. 3. Periodic calibration and calibration of measuring instruments. 4. Working with an ultrasonic thickness gauge. 5. Direct work on measurements of manufactured products on the LM3D CMM. 6. Analysis of product defects and assembly body based on the data obtained during the measurement. 7. Analysis of defects of stamped parts on projects (RF - 90, LB1A, X - 52, XGA, Vesta) of cars (LARGUS, NISSAN ALMERA, RENAULT LOGAN, RENAULT SANDERO STEPWAY, VESTA, X-RAY). 8. Analysis of measurements of the geometry of the part and providing, during the detection of the defect, a plan of corrective actions to the production shop. 9. Filling, analysis, and respecification of "GREEN SHEET". 10. Correction of geometric dossiers, work in eROOM and GEOM systems. 10. Conducting technological documentation. 11. Acceptance, certification and operation of control devices. Targeted professional quality responsibilities: 1. Geometric analysis of parts of mass production. 2. Development and implementation of documentation on geometry at various stages (MONT, ATFMR, PSW, SERIE). 3. Ensuring a balance between functional needs and production capabilities. 4. Conducting an analysis of projects and production capacities necessary to understand the problems of implementing prototypes. 5. Achieving the proper quality level of your control area 6. Develop and implement a surveillance plan and related defect schemes. 7. Making a proposal to improve standards. 8. Participation in supplier audits. 9. Monitoring compliance with geometry requirements at the product / process concept stage. 10. Presentation of results and solutions of various simulations, calculations and theoretical calculations. 11. Participation and issuance of technical specifications for the design and manufacture of control equipment. 12. Development of FRA charts 13. Development of FPC charts 14. Keeping statistics measurements. 15. Development of FOP charts 16. Certification of equipment and processes for technological accuracy, by means of determining the indices Cm, Cmk, Cp, Cpk. 17. Maintenance and improvement of processes according to ISO 9001/16949/14001/18001 standards. 18. Organization and participation in brainstorming with the construction of the Ishikawa diagram and further analysis of the problem using the principle of the diagram and Pareto's law. 19. Active use of the "5 Why" method in solving quality problems. 20. Development of process maps. 21. Work with customer complaints and claims (preparation of reports 8D). 22. Preparation of product quality standards. 23. Knowledge and work on standards and methods of SPC, MSA, 8D, APQP, PPAP, QRQC. 24. Development, implementation and maintenance of documentation (procedures, instructions, regulations, etc.) on the QMS up to date. 25. Ensuring the implementation of procedures, instructions, provisions of the QMS, maintaining the necessary records.

Participation in the LADA Personal Manager project. The representative of OAO "AvtoVAZ" on the project VESTA, X-RAY in Smolensk. Comprehensive help and support for owners of new cars Vesta and X-RAY on all issues, wishes and claims related to the car. Participation in the acceptance of vehicles with auto transporter (UNLOADING). Control the implementation of pre-sale preparation in full, according to the instructions of the PSP (PDI). Monitoring compliance with the requirements of the program "LAUNCHING (TASK FORCE)" Verification of compliance of the DC to the check-list, brand book of the company Preliminary analysis of defects and preparation of checklists for all Vesta & XRAY defects affecting unfamiliar defects Help DC in the implementation of regulations, methods to eliminate inconsistencies. Assistance to representatives of the DC in matters related to the supply of repair parts and cars, to design of DC in accordance with the brand book, and working methods. Compilation of daily photos and text reports. Operational communication with the Customer Satisfaction Center(CSC), to help DC and solve unfamiliar problems. Prompt execution of tasks from the CSC for the control and correction of defects on commercial cars.